90 degree bends are used to connect two pieces of UPVC pipe that are at right angles to each other, with a sweeping bend in between. The advantage of a bend over a 90 degree PVC elbow is that there is less friction loss because the flow characteristics are so much better.

90 degree bends are used to connect two pieces of UPVC pipe that are at right angles to each other, with a sweeping bend in between. The advantage of a bend over a 90 degree PVC elbow is that there is less friction loss because the flow characteristics are so much better.

90 degree bends are used to connect two pieces of UPVC pipe that are at right angles to each other, with a sweeping bend in between. The advantage of a bend over a 90 degree PVC elbow is that there is less friction loss because the flow characteristics are so much better.

The Pass Over Bend is a transition fitting that allows a pipe to be "passed-over" without tearing apart the current plumbing system. This fitting aids in joining vertical pipes while avoiding the running lines' obstructing pipe.

The Pass Over Bend is a transition fitting that allows a pipe to be "passed-over" without tearing apart the current plumbing system. This fitting aids in joining vertical pipes while avoiding the running lines' obstructing pipe.

The Pass Over Bend is a transition fitting that allows a pipe to be "passed-over" without tearing apart the current plumbing system. This fitting aids in joining vertical pipes while avoiding the running lines' obstructing pipe.

The Pass Over Bend is a transition fitting that allows a pipe to be "passed-over" without tearing apart the current plumbing system. This fitting aids in joining vertical pipes while avoiding the running lines' obstructing pipe.

The Pass Over Bend is a transition fitting that allows a pipe to be "passed-over" without tearing apart the current plumbing system. This fitting aids in joining vertical pipes while avoiding the running lines' obstructing pipe.

The uPVC White Bottom Offset Bend from Flop last is required to finish soil and waste system installations. The Bend should be used in conjunction with the Flop last soil and waste system since it is dependable and simple to install.

The uPVC White Bottom Offset Bend from Flop last is required to finish soil and waste system installations. The Bend should be used in conjunction with the Flop last soil and waste system since it is dependable and simple to install.

The uPVC White Bottom Offset Bend from Flop last is required to finish soil and waste system installations. The Bend should be used in conjunction with the Flop last soil and waste system since it is dependable and simple to install.

A gadget called a circuit tester is plugged into an electrical outlet to check the wiring. A circuit tester features a number of lights that display the wire in the outlet's condition, enabling the technician to confirm that it was installed correctly.

A gadget called a circuit tester is plugged into an electrical outlet to check the wiring. A circuit tester features a number of lights that display the wire in the outlet's condition, enabling the technician to confirm that it was installed correctly.

A gadget called a circuit tester is plugged into an electrical outlet to check the wiring. A circuit tester features a number of lights that display the wire in the outlet's condition, enabling the technician to confirm that it was installed correctly.

A form of tank fitting called a tank connector is also referred to as a tank inlet, tank outlet, or tank nipple. Due to its dependence on the water supply, this fitting must be leak-proof. Tank connectors come in numerous variants.

A form of tank fitting called a tank connector is also referred to as a tank inlet, tank outlet, or tank nipple. Due to its dependence on the water supply, this fitting must be leak-proof. Tank connectors come in numerous variants.

A form of tank fitting called a tank connector is also referred to as a tank inlet, tank outlet, or tank nipple. Due to its dependence on the water supply, this fitting must be leak-proof. Tank connectors come in numerous variants.

A form of tank fitting called a tank connector is also referred to as a tank inlet, tank outlet, or tank nipple. Due to its dependence on the water supply, this fitting must be leak-proof. Tank connectors come in numerous variants.

SUPREME AQUA GOLD MOULDED PIPE FITTING ELBOW 90 DIGREE - SCH80 ELBOW 90 DIGREE (Size-32mm) - In order to join tubes at a 90° angle, 90° pipe elbows are utilized. The elbow is always shaped like a right angle, as its name suggests. Such an elbow is sometimes referred to as a "90 bend" or "90 ell." This is a pipe fitting tool that has been bent to make a 90° change in the direction of the fluid or gas flowing through the pipe.

A form of tank fitting called a tank connector is also referred to as a tank inlet, tank outlet, or tank nipple. Due to its dependence on the water supply (both internally and externally), this fitting must be leak-proof. Tank connectors come in numerous variants.